Table of Contents
Watch the video: “How to Set Up Your Brother PR670E Professional Embroidery Machine” by Frank Nutt Sewing Machines
A new multi-needle is an investment—and the first setup can feel like a lot all at once. This walkthrough translates the full video into a clear, step-by-step guide you can follow at your own pace.
By the end, you’ll know exactly how to unbox safely, assemble the thread stand, power on and calibrate, thread a needle and bobbin, and attach a hoop without bumping the needle bars.
What you’ll learn
- How to unbox and organize all included accessories without missing key packaging pieces
- The correct way to secure the machine on its stand and assemble the thread stand
- Power-on essentials: screen prompts and automatic arm calibration
- Reliable threading and bobbin insertion (clockwise) fundamentals
- Safe hoop attachment and what “normal wobble” actually looks like
Getting Started: Unboxing Your Brother PR670E
Initial Unpackaging and Strap Removal The PR670E ships in a tall, heavy box—clear a spacious, stable area before you begin. Start by cutting and removing the large shipping straps that bind the box. Take your time and keep the blade angled away from the cardboard so you don’t nick anything inside.
Watch out
- The box and internal shells are bulky—lift carefully and enlist help if needed.
Accessing and Removing Accessories Lift the top flaps following the printed instructions. Inside you’ll find a polystyrene tray holding accessories—remove this and set it to one side so you can inventory later. You’ll also find additional cardboard-sided polystyrene inserts along the sides; these pull out to reveal more contents.
Pro tip
- Keep accessory bags grouped in a shallow tray so small parts (like screws and the supplied tools) don’t wander while you work.
Releasing the Outer Box Sleeve This carton uses six plastic clips around the lower edge. Squeeze the bottom of each clip, pull up, and pop it free. Work around the box until all six are removed. Then slide the entire outer sleeve up and away to reveal the inner packing.
Quick check
- Did you find and remove all six clips? The sleeve should lift straight up without snagging when they’re all disengaged.
Assembling the Machine for First Use
Mounting the Machine on its Stand With the last polystyrene shell visible, remove any tape and shells to expose the machine. The video places the machine on the official Brother PR/VR stand (this stand is an additional purchase). Lock the corners and tighten the bolts—there’s one at the front corner and another at the back. Once tightened, the machine should feel rock solid.
From the comments
- Several new owners ask about workspace and heavy lifting. The video team moved the machine to an upstairs demo room after unboxing—plan your route and get a second person to help if stairs are involved.
Removing Protective Packaging and Tape Carefully peel away every piece of blue transit tape; look around the arm and moving parts. Gently remove any small polystyrene blocks tucked in to stabilize components. This is essential—leftover tape or packing can block movement.
Setting Up the Thread Stand The thread stand is nested under a protective cardboard cover. Cut the tape and remove the cover. Bring the stand body upright, then swing the display to the front. Tighten the display’s base with the supplied plastic-bolt tool until it’s secure.
Next, open the two side sections where threads will route. Loosen their bolts, position the arms to level/horizontal, and re-tighten. Insert the extra support screw at the base for added stability; the supplied screwdriver makes this easier. When everything’s locked, nothing should wobble.
Watch out
- Stiff bolts are normal from the factory—use the provided tool rather than forcing by hand.
Powering On and Initial Machine Setup
Connecting to Power and Boot-up Plug in the power lead and switch on the machine. Touch the display to wake it. You may be prompted to set the clock; the video skips this for brevity.
Screen Calibration and Language Selection Allow the machine to perform its automatic arm calibration sequence. Choose your screen language (English is shown in the video) and proceed to the home screen. Now you’re ready to thread.
Quick check
- The arm will do a short “jig” during calibration—that’s normal and confirms the system is aligned.
Threading Your Brother PR670E
Detailed Needle Threading Steps Place a spool on the #1 spindle. Route the thread straight up from the spool to the first guide on the stand, then into the tension path—follow the guide all the way around the tension dial, under the upper flap, and through the lower guides. Follow the #1 path down toward the needle.
At the needle area, there’s a small wire guide above the needle—use tweezers to place the thread there cleanly. Engage the automatic needle threader to finish the job, then trim the excess using the built-in cutter. The same path repeats for needles 2 through 6, so once you’ve threaded one, the rest feel familiar.
Pro tip
- If the thread doesn’t seat correctly somewhere in the path, tension will be off. It’s faster to re-thread carefully than to chase tension issues later.
Correct Bobbin Insertion and Orientation Open the bobbin area and load one of the pre-wound bobbins included in the accessories. These have a magnet core that faces the back. Confirm that the bobbin unwinds clockwise—this matters for correct tension. Feed the thread through the tension slit and under the small clip. Push the bobbin case onto the spindle until you hear a clear click (or firmly seat it if you’re holding the lever). Trim the tail to about 4 inches and tuck it in front.
Watch out
- If the bobbin runs anti-clockwise, you may see loose, loopy stitching and the machine won’t detect a “snap.” Reseat it so the unwind is clockwise.
Preparing for Embroidery: Hoops and Needles
Attaching the Frame Holder and Hoop Attach Frame Holder A (the one intended for the supplied hoops) by sliding it under the needle bars and onto the locating pins. Replace the screws and finger-tighten; you can snug them with the supplied tool if needed. On the side, loosen the large screw to adjust width—there are notches that correspond to hoop sizes. Set the notch that matches your hoop, then tighten again.
Slide the hoop into position under the two metal flaps on the frame holder. It should seat smoothly; a normal amount of “wobble” is expected by design. To remove, push up from below and slide the hoop out while keeping it clear of the needle bars.
From the comments
- A viewer asked if the slight hoop movement is normal; the creator confirmed it is. If you feel unusual resistance, double-check the holder width and ensure you’re not contacting the needle bars.
Important Notes on Needles and Maintenance The PR670E uses flat-sided domestic needles. The video shows HAx130EBBR #11 as an example of a compatible type. Industrial needles are not appropriate here. If you’re uncertain, compare with the spares included in your accessory kit or check one installed needle to verify the flat side faces the back.
Quick check
- Flat side of the needle shank should face the back—consistent with domestic needle orientation.
Troubleshooting Essentials (Based on the Video)
- Hoop won’t attach: Re-check your frame holder width notch for the hoop you’re using; don’t force it.
- Loopy stitches after bobbin change: Confirm clockwise unwind through the bobbin tension path.
- Threader won’t catch: Ensure the thread is in the final wire guide above the needle before engaging the auto-threader.
- Machine won’t start the first time: Verify the power cable connection and that the arm completed its automatic calibration.
From the comments: Community Q&A highlights
- Availability and price: Not specified in the video or comments—contact the retailer directly for current details.
- Wide table extension for PR670E: Not addressed in the video; check with your dealer or Brother support.
- Oiling schedule: The video doesn’t cover lubrication. Consult your PR670E manual or dealer for the correct interval and location.
- Restarting after a stop and enlarging fonts: Not covered in this setup video; refer to the machine’s on-screen help and manual, or the channel’s more in-depth screen/operation video.
- Magnetic hoop for a single-needle VR: This video focuses on the PR670E multi-needle; compatibility and fitting steps for the VR are not shown.
Conclusion and Next Steps You’ve unboxed, secured the machine, set up the thread stand, powered on and calibrated, threaded your first needle, inserted the bobbin correctly, and attached a hoop. That’s the full setup path to your first stitch.
To keep going, explore the channel’s “more extensive” video for screen functions, editing, and actual stitching. And if you hit a snag, note where in this guide the step lives so you can retrace quickly.
Buyer’s notes and extras
- Stand: The video uses the official PR/VR stand; it’s an extra purchase but offers convenient storage.
- Accessories: Pre-wound bobbins, tools (including a screwdriver and tweezers), and spare needles come in the accessory kit.
- Calibration: Expect the arm to move during boot as it self-checks alignment—this is normal and should happen each time you power up.
Safe-handling checklist before first stitch
- All blue transit tapes removed
- Thread stand bolted and supported
- Frame holder sized to the hoop notch
- Bobbin clockwise and clicked in
- Needle threaded with the wire guide engaged
- Hoop installed without contacting needle bars
Skilled-user tip Once you’ve mastered a single path, thread all six needles the same way while your steps are fresh. Label spools if you’re testing color layers so you can repeat results later.
About sizing and accessories (general, not brand-specific to this video) If you’re comparing accessory ecosystems for different machines, consider how your hoops, magnetic frames, and cap systems adapt to your projects over time. Some accessories are brand or model specific, so verify compatibility with your exact machine before purchase. brother embroidery machine
If you’re building a multi-needle workflow and also own a single-needle model in the studio, note that hoop and frame compatibility often differs between classes—even within the same brand family. For instance, a multi-needle frame may not fit a single-needle model without a dedicated adapter. brother vr
When you start adding specialty frames, check whether your machine supports them natively or with optional attachments. This includes sash-style options—understanding how your machine’s arm clears flexible or long materials helps you choose the right upgrade. brother magnetic sash frame
Before purchasing new hoops, confirm sizing notches and ranges your frame holder supports so you can move between small and larger field hoops without guesswork. A quick reference card with the notch positions you use most can save time. brother embroidery hoops sizes
As your project list grows, a modular approach to frames is helpful. Look at options specifically designed for your machine series and confirm the mount pattern and clearances match your holder. brother magnetic frame
If you frequently work on thick items like jackets, you may explore compatible clamping or magnetic systems designed for your machine series. Always verify the exact model fit before you buy. brother hoops
Owners of this series sometimes add specialty magnetic systems designed for PR models; confirm the specific fit for your PR generation before purchasing. mighty hoops for brother pr670e